Mag Drive
The Johnson Pump range of magnetic drive centrifugal pumps has no
seals and is therefore leak proof. This makes the pumps ideal for pumping hazardous, toxic, explosive, aggressive or valuable fluids. Because of more stringent environmental requirements and ever more advanced manufacturing process, there is increase in interest in this type of pump.
CombiMag CombiMagBloc MDR-series
CombiMag
Mag drive horizontal centrifugal pump to ISO 5199 and ISO 2858 /EN 22858
| Features | ||
| • | 100% leakfree | |
| • | Long life cycle, reduced maintenance costs |
|
| • | Flanges according to ISO 7005 PN 16 |
|
| • | For stainless steel execution ISO 7005 PN20 / 150 lbs ANSI B 16.5 available |
|
| • | Outstanding hydraulic performance |
|
| • | High efficiency impeller |
|
| • | Closed impeller with back vanes providing axial balancing of impeller loads |
|
| • | Half open impeller with wear plate |
 |
| • | Easy maintenance through the Back-Pull-Out principle |
|
| • | Atex certification |
|
| • | Outer rotor with safety bearing |
|
| • | Somarium Cobalt high performance magnets |
|
| • | Containment can in Hastelloy® for limited eddy current losses |
|
| • | Silicon carbide pump liquid lubricated internal bearings |
|
| • | Heating jackets optional |
|
| • | Grease or oil bath lubricated bearings |
|
| • | PT 100 temperature monitoring |
|
| • | Interchangeable with existing ISO 2858 pumps |
|
Suitable for
Clean liquids, slightly contaminated but
the impurities must not be abrasive
or magnetic
| Technical data | |
| Casing: |
Cast iron, Nodular cast iron,
Stainless steel, Stainless steel alloys, Nickel based alloys, Duplex |
| Impeller: | Cast iron, Bronze, Stainless steel, Stainless steel alloys, Nickel based alloys, Duplex |
| Max. capacity: 500 m3/h | |
| Max. delivery head: | 160 m |
| Max. liquid temperature: | -50 up to 350°C |
| Max. system pressure: | 1600 kPa (16 bar) |
Max. viscosity: |
150 mPas |
Min. viscosity: |
0.3 mPas |
| Max. speed: | 3 600 rpm |
Downloads
(Sales brochure, Data Sheet, Instruction Manual)
Back to the Top
CombiMagBloc
Closed coupled magnetic drive horizontal centrifugal pump
to ISO 5199 and ISO 2858 /EN 22858
| Features | ||
| • | 100% leakfree |  |
| • | Long life cycle, reduced maintenance costs |
|
| • | Flanges according to ISO 7005 PN 16 |
|
| • | For stainless steel execution ISO 7005 PN20 / |
|
| • | Outstanding hydraulic performance |
|
| • | High efficiency impeller |
|
| • | Closed impeller with back vanes providing axial balancing of impeller loads |
| • | Half open impeller with wear plate |
| • | Easy maintenance through the Back-Pull-Out principle |
| • | Standard IEC flange motor |
| • | Atex certification |
| • | Outer rotor with safety bearing |
| • | Somarium Cobalt high performance magnets |
| • | Containment can in Hastelloy® for limited eddy current losses |
| • | Silicon carbide pump liquid lubricated internal bearings |
| • | Heating jackets optional |
| • | PT 100 temperature monitoring |
| • | Interchangeable with existing ISO 2858 pumps |
Suitable for
Clean liquids, slightly contaminated but
the impurities
must not be abrasive
or magnetic
| Technical data | |
| Casing: |
Cast iron, nodular cast iron, stainless steel, Stainless steel alloys, Nickel based alloys, Duplex |
| Impeller: | Cast iron, stainless steel, bronze, Stainless steel alloys, Nickel based alloys, Duplex |
| Max. capacity: 280 m3/h | |
| Max. delivery head: | 140 m |
| Max. liquid temperature: | -50 up to 200°C |
| Max. system pressure: | 1600 kPa (16 bar) |
Max. viscosity: |
150 mPas |
Min. viscosity: |
0.3 mPas |
| Max. speed: | 3 600 rpm |
Downloads (Sales brochure, Data Sheet, Instruction Manual)
Back to the Top
The MDR-series
in PP and PVDF
Mag Drive seal-less centrifugal pumps are virtually leak-proof since
the design eliminates the multitude of problems related to shaft seals and
packings.
| Features/Benefits |  |
|
| • | No leaking shafts | |
| Improved safety | ||
| • | High corrosion resistance | |
| Wide range of applications | ||
| • | Standard electric motors | |
| Simple and inexpensive replacement | ||
| • | Reliable in performance | |
| Less down-time | ||
| • | Simple design | |
| Easy maintenance | ||
Suitable for
Sulphuric acid, caustic, sodium hydroxide, developer, fixing bath,
bleaching agent, various other chemicals
| Technical data | |
| Casing: |
PP filled with glass fibre, PVDF with carbon fibre |
| Impeller: | PP filled with glass fibre, PVDF with carbon fibre |
| Max. capacity: 30 m3/h | |
| Max. delivery head: | 24 m |
| Max. liquid temp: | 85°C for PP, 100°C for PVDF |
| Max. system pressure: | 3 bar at 20° C |
| Max. speed: | 2 800 rpm |
Downloads
(Sales brochure, Data Sheet, Instruction Manual)
Back to the Top